Sunday, December 5, 2010

Projects and assessments

Install and commission commercial refrigeration and air conditioning

Level
3
Credits
15


Purpose       This unit standard is for people who work, or intend to work, in the refrigeration and air conditioning sector of the engineering industry, and is intended for use in the training of installers and technicians of refrigeration and air conditioning equipment.

                        People credited with this unit standard are able to: demonstrate knowledge of pre-installation activities for refrigeration and air conditioning systems; install the components of refrigeration and air conditioning systems; perform pre-start commissioning procedures; perform start-up commissioning procedures; and provide information to operators and complete required documentation.

Subfield
Mechanical Engineering
Domain
Refrigeration and Air Conditioning
Status
Registered
Status date
20 June 2006
Date version published
20 June 2006
Planned review date
31 December 2011
Entry information
Open.
Replacement information
This unit standard replaced unit standard 3834 and unit standard 3839.
Accreditation
Evaluation of documentation and visit by NZQA.
Standard setting body (SSB)
Competenz
Accreditation and Moderation Action Plan (AMAP) reference
0013


Special notes

1       References
          Building Act 2004;
          Electricity Act 1992;
          Electricity Amendment Act 1997;
          Hazardous Substances and New Organisms Act 1996;
          Health and Safety in Employment Act 1992;
          Ozone Layer Protection Act 1996;
          Electricity Regulations 1997;
          AS/NZS 1677:1998, Refrigerating systems – Refrigerant classification;
          AS/NZS 3000:2000, Electrical installations;
          Code of Practice for the reduction of emissions of fluorocarbon refrigerants in refrigeration and air conditioning applications.  Institute of Refrigeration, Heating and Air Conditioning Engineers of New Zealand (IRHACE New Zealand), 2001.  Available from IRHACE, 28 E Lambie Drive, Manukau City.

2       Definitions
          Commercial refrigeration and air conditioning systems refers to items such as: refrigeration equipment as found in retail food outlets, truck and shipping-container refrigeration, horticultural cool room refrigeration, controlled atmosphere fruit stores;
          and air conditioning equipment as found in commercial buildings.
          Organisational procedures refer to documents that include: organisational rules, codes, and practices; equipment operating instructions; production specifications; documented quality management systems; and health and safety requirements.

Elements and performance criteria

Element 1

Demonstrate knowledge of pre-installation activities for refrigeration and air conditioning systems.

Performance criteria

1.1              Installation drawings, schedule of materials, and instructions are described in terms of checks that should be made against site conditions.

1.2              Two examples are given of modifications that may be required to suit site conditions.

1.3              Procedures for assembling materials and verifying them against a schedule of materials are described.

1.4              Procedures for verifying ancillary service connections and reporting any discrepancies are described.

Range           may include but is not limited to – water, electricity, plumbing.

1.5              Two examples are given of situations where permits and/or consents are required for installations.

Element 2

Install the components of refrigeration and air conditioning systems.

Performance criteria

2.1              Major components are positioned and secured in accordance with drawings, designs, specifications, and instructions.

Range           refrigeration components include but are not limited to – compressor, condenser, evaporator, metering device;
                        air conditioning components include but are not limited to – compressor, outdoor fan coil, metering device, indoor fan coil.

2.2              Ancillary components and installation materials are installed in accordance with drawings, designs, specifications, installation considerations, and instructions.

Range           ancillary components may include but are not limited to – valves, controls, filters, driers;
                        installation materials may include but are not limited to – supports and bracketing to secure pipework, piping, tubing, capping, thermal insulation;
                        installation considerations may include but are not limited to – nitrogen purging, internal cleanliness.

2.3              The work of associated tradespeople is identified and reported in accordance with organisational procedures.

Element 3

Perform pre-start commissioning procedures.

Performance criteria

3.1              Safety devices are tested and calibrated and systems are verified as safe to be exposed to operating pressures.

3.2              Controls are tested and set to meet specified performance and safety requirements.

Range           controls equipment may include but is not limited to – programmable logic control (PLC), electronic, electromechanical, pneumatic.

3.3              Electrical systems are checked, and compliance with performance and safety requirements is verified.

Range           checks include but are not limited to – earth continuity, insulation resistance, polarity, voltage.

3.4              Visual and tactile tests are performed to ensure the mechanical integrity of all electrical terminations and connections.

3.5              Motor ratings are verified against fuse ratings and overload settings.

3.6              Motor and pump rotation directions are verified.

3.7              Fluid flows are tested and balanced as required.

3.8              Actions are taken as required to clear foreign solid matter from pipe-work and/or associated components.

3.9              System and component integrity is confirmed by the use of appropriate leak detection methods and equipment.

3.10           Compressor is checked and, if required, charged with appropriate lubricant.

3.11           System is evacuated to pull down to 500 microns or less to ensure that moisture, oxygen, and non-condensables are removed.

Range           evacuation tools include but are not limited to – Schraeder core removal tool, vacuum analyser, vacuum pump, short large-bore vacuum hose, solenoid valve, isolating valves.

3.12           Where triple evacuation is required, vacuums are broken with dry nitrogen.

3.13           Vacuums are broken with appropriate refrigerant after final evacuation.

Element 4

Perform start-up commissioning procedures.

Performance criteria

4.1              System is checked and charged using appropriate method and refrigerant in accordance with system specifications.

Range           method may include but is not limited to – suction super-heat set and sub-cooling checked after system is running and stabilised, compressor current measured and control settings verified for operational performance, lubricant and/or refrigerant levels and flows adjusted as necessary for required performance.

4.2              Lubricant and/or refrigerant identification labels are affixed to appropriate parts of the system in accordance with legislative requirements.

4.3              System performance data is recorded as required by operational specifications and instructions.

Range           temperatures, pressures, super-heat, sub-cooling, current draw, fluid flows, humidity, noise, vibration.

Element 5

Provide information to operators and complete required documentation.

Performance criteria

5.1              Operators are familiarised with manuals and operating instructions.

5.2              Operators are instructed to operate refrigeration and air conditioning systems within design parameters, and in accordance with operational and worksite procedures.

5.3              Documentation is produced outlining labour and materials used, and any details required for a warranty in accordance with organisational procedures.

Please note

Providers must be accredited by the Qualifications Authority, or an inter-institutional body with delegated authority for quality assurance, before they can report credits from assessment against unit standards or deliver courses of study leading to that assessment.

Industry Training Organisations must be accredited by the Qualifications Authority before they can register credits from assessment against unit standards.

Accredited providers and Industry Training Organisations assessing against unit standards must engage with the moderation system that applies to those standards.

Accreditation requirements and an outline of the moderation system that applies to this standard are outlined in the Accreditation and Moderation Action Plan (AMAP).  The AMAP also includes useful information about special requirements for organisations wishing to develop education and training programmes, such as minimum qualifications for tutors and assessors, and special resource requirements.

Comments on this unit standard

Please contact Competenz qualifications@competenz.org.nz if you wish to suggest changes to the content of this unit standard.


DIPLOMA TRANSPORT PROJECT

Prepare a unit quote and approximate running cost for the first twelve months of use including service costing.

The following parameters can be assumed to be given for all examples.
Summer average daytime ambient temp   28 c
Summer average night ambient temp         15 c
Winter average daytime ambient temp      12 c
Winter average night ambient temp             5 c

The first vehicle will be a semi-trailer, multi-temp unit carrying 7tons of ice-cream at -25c, at a maximum weight of 900kg/pallet, also 12tons of butter at 5c,at the same maximum pallet weight.
The second vehicle will be a 7.5ton rigid single temp vehicle to carry up to 4tons of frozen products at a minimum of -20c, at a maximum pallet weight of 800kg/pallet.
It is to be assumed the trailer is on trunking duty between Auckland and wellington ,leaving at 5am taking 12hours, returning with dry-freight the fridge unit switched off. Three runs/week to be carried out following this timetable.
The rigid however is to carry-out multi-drop duties in Auckland, this will cover a five day working week, twenty (20) drops /day of 10 mins duration. each day comprising 10hrs, also starting at 5am each day.
The units are to be built to N.Z. normal build standards which you are to research, the most fuel efficient design is to be used. Food standard guidelines are to be strictly adhered to in all cases.
The units to be used have been specified by the customer to be CARRIER, the vehicle bodies are at your discretion, you are to follow manufacturers recommended service intervals, service costs are as follows:-
First service 400hrs      F.O.C.      (all units )
1000hr service             $   450        rigid units
1000hr service             $   700       trailer units
5000hr service              $ 1200      rigid units
5000hr service               $1500       trailer units

You are only to use the guidelines and selection tables supplied to size the units , running times are  to be calculated by thermal loss through body , a 20% air change per door opening in the case of multi-drop usage and all products are  at correct temperature on loading. Trunking usage you can assume no door openings during transit.
Daytime average temperatures are to apply 9am to 9pm, all operations outside these times you are to apply night temperatures.
Fuel usages are as follows:-
Truck unit low speed    3ltrs/hr
Truck unit high speed    4.5ltrs/hr
Trailer unit low speed    4ltrs/hr
Trailer unit high speed   7ltrs/hr
All units will start in high speed, will run on high speed until within 3 degrees of set-point, then run on low speed down to set-point and stop. Units will not restart until 3 degrees above set-point and will always restart in high-speed.

The effects of any surface cooling due to windage while travelling are to be ignored, as are any losses due to vehicle body damage or moisture ingress at seams. These are to be considered as new vehicles.



Tuesday, November 23, 2010

YEP!! still typing....

The approach of totaly student driven learning that is I admit still a distant spectre on the horizon, the practical considerations and the effect on the professional and personal lives of tutors of such a system and its allied assessment methods are still to be broached. There will be a day when this is a viable approach, however this will probably not be in the foreseeable future. There is a movement towards a more student driven assessment methodology however, if this is an improvement or just the current in-vogue train of thought prevalent among those we must obey, is still to be proved. In my experience or to be exact my wife,s experience of " student self-assessment ", the main effect of this currently much enthused about piece of assessment new-age dogma was to bring approximately half the group to ask " if we are doing this why are we paying for a tutor??? ".The new ideas of these approaches to both teaching and assessment must be used with care and careful preparation by the user, the opportunity for improvement in both areas is clearly demonstrated in John Hattie,s Meta-Analysis and the improvement shown or detrimental effects of the various ideas is given as a quatifiable ratio. How individuals interpret and apply the various forms of educational, teaching, assessment and learning ideas will obviously change the outcomes of these methods.
There are other factors that will also have to be taken into account, as much as we are being encouraged to design around and employ these all encompassing  "new-wave" ( there,s a blast from the past ) this will fix it " vunder-metods", we have to remember that our abilities as assessors vary greatly, but far more importantly our students abilities as learners vary almost infinitely more than we can possibly imagine. Their learning is influenced by factors far to many to list in such a commentary home enviroment, peer pressure, indvidual ability, enthusiasm, interest, maturity and socio-economic background to mention just a few of these contributing forces. That among others are all affecting learning outcomes for the students and thus their ability to not only apply their learning in an assessment or to an assessment task, but to be able to cope with the assessment enviroment itself.
No matter how we dress it up or what terminology we use a test is a test in anybodies language! We must above all be honest with ourselves and more importantly with the students. Failure is an option!!! There I,ve said that most deep, dark and deplorable of phrases, " he who shall not be named", has been spoken of , as much as we must endeavour to provide a supportive learning enviroment, with a truthful and fair assessment criteria, using the best tools at our disposal. We must never comit that most heinous of educational offences," pandering to the fashion of the day". When all said and done it is our name on the Doctors degree, Nurses diploma, Coaches C.V. and Kindergarten teachers R.O.L. To be honest is sometimes disappointing, sometimes deeply discouraging and occasionaly downright brutal. It is however the truth, as distastful as that may be it is a fact of life! We cannot and must not design an assessment no matter how well meaning its intent, that is intended to produce an outcome rather than measure an effect. Some may feel that this is a rather jaundiced view of what we are trying to achieve, but it has been said to us that " we are just plucked from industry and stuck in front of a class and expected to teach".But for me that poses a question, can you take the veiw that purely theoretical knowledge is enough, or do we gain something more through practical employment of that knowledge??. That perhaps is why we are here , we have the knowledge in our own fields to make such a judgement call to assess if someone has learnt enough to be released upon the unsuspecting world. We are here to hone the skills to improve our abilities at doing that, making that judgment call.
Likewise with assessment the level of comprehension of a given subject or skill cannot be and must not become a dogmatic diatribe of "only this will do",or conversely the opposite side of the coin the " she,ll be right " methodology, this is surely what we are here to learn. How we apply what we know to ensure that those we teach are competent at what we expect them to have learnt and how to use that aquired knowledge correctly.
I think it does all come down to the fact that we (according to a bunch of other jokers) know our own subjects, what we are trying to do is make sure that those that follow us also know what they are doing!!! If we fail to carry out this task honestly then the only people to carry the blame for this failure is ourselves, of this I am sure. We have been given a number of tools and methods to measure not only our students success but also our own! I for one will be using and in fact have already employed some of these methods, the system I was educated in does make some ideas difficult to cope with, but that,s why we are here isn,t it????

Monday, November 22, 2010

ASSESSMENT!

Been trying to get this to upload electronically but no joy so back to good old keyboard bashing!!

Coming from a formal and structured enviroment of the English scholastic system of the 1960s and 1970s, the terminology, methodology and fundamental ethos of assessment in that period differ from today in almost every respect.
The ideas and principles of today have created a focus on student enrichment rather than information indoctrination. We have explored the ways and means of achieving this new levelof intra-personal communication and interaction over the last few months. Some of the ideas put forward seem almost alien to me and if employed in the wrong context detrimental to our primary purpose.
It is my understanding that the whole purpose of assessment is to guage the students ability not only to learn information by rote, as was the case in the past, but to gain the ability to both interpret and employ their learning to advance their personal development.While this may seem a very theoretical definition of the subject, the meaning is self evident. Today the focus of teaching is changing to produce a student orientated enviroment, perhaps at the cost of devaluing the actual content. The phrase "dumbing-down", is becoming more and more common even in the short time I have been in education.
Compared to the plethora of subjects I was required to learn as part of my training, the subject of engineering in general has lost some of its most fundamental skills. If this trend carry,s over into the field of assessment then are we not in danger of creating an albatross that will be hanging around the neck of the industry for years to come. We may in our best intentioned efforts to become more pro-active, engaging and nurturing, allied with the current headlong dash to deliver "blended-learning", self-assessment and virtual rather than practical teaching exercises, might be working on the wrong subjects. The same pitfalls abound in our approach to assessment, both formative (progress tests) and summative (final exams), sorry about the old school , unfashionable terminology but jingoism has never been my forte. It is our purpose to make sure that when we write a test, ('ooops! gone old school again), that it not only fulfils the criteria laid down by 'those who must be obeyed', but also the practical needs of the subject being taught,the depth of knowledge, understanding,ability and skill required of the student at that particular level of learning

Tuesday, November 16, 2010

getting there

well finally got this under-way just have to get all the prior stuff on to the page, this should be good.